You have a large exterior panel to source for a 2027 program. The fiberglass version comes back with cosmetic rework on parts you did not budget for. The stamped metal version is heavy enough that two people on the line have to handle it. The injection-molded version requires a tool that will cost more than the program will ever pay back at your volume.
That gap is where heavy-gauge thermoforming does its best work. A single sheet of plastic is heated and formed over a single-surface aluminum tool, so tooling runs roughly 10 to 15 percent of what an injection mold costs for a part with the same footprint, and first-article parts land in 15 to 20 working days. On an RV program building a few hundred to a few thousand units a year, that changes which redesigns you can justify.
The industry is running at a volume where this decision comes up constantly. RV wholesale shipments finished 2025 at 342,220 units, up 2.5 percent over 2024, and the Spring 2026 RV RoadSigns forecast prepared by ITR Economics puts 2026 in a range of 328,800 to 367,000 units with a median of 349,000 (RVIA). Healthy volume for a vehicle industry. Still well under what it takes to pay off an injection molding tool across a single floor plan.
Heavy-gauge thermoforming produces single parts up to 6 feet by 10 feet on one tool, which covers most of the large panels on an RV: front and rear caps, roof and slide-out components, wheel wells and fender skirts, storage compartment liners, interior wall and ceiling panels, and equipment shrouds. A part that size in metal needs a large press and a multi-stage die, and the same shape in fiberglass gets its cost from hand labor and cosmetic rework.
The size ceiling matters more on an RV than on almost any other vehicle, because RV parts are dimensionally large and structurally modest. A storage compartment liner has to be watertight, impact resistant, and cosmetically acceptable. It does not have to carry a crash load. That combination is exactly what a formed sheet does well, and it is where the weight comes out.
718 lbs → 38 lbs
One heavy equipment OEM replaced a steel drive belt guard weighing approximately 718 pounds with an impact-resistant ABS thermoformed part weighing 38 pounds, a 95 percent weight reduction that let one technician remove the cover by hand instead of bringing in a forklift.
The practical limit is set by sheet thickness and draw ratio, well before outline dimensions become an issue. Deep draws in a corner, sharp radii, and tight tolerance features are where a design review earns its keep before tooling is cut.
At PCI we form parts up to 6 feet by 10 feet with CNC trim, in ABS, HDPE, HMWPE, polycarbonate, polystyrene, PVC, TPO, nylon, TPR, and laminates, with tooling, engineering, and manufacturing under one roof in Elkhart.
Part consolidation is where thermoforming pays for itself on an RV build, and it is usually worth more than the piece price of any single component. A bracketed, bonded, and riveted assembly of stamped panels, fiberglass sections, and trim pieces can often be redrawn as one formed part with the features molded in: mounting bosses, stiffening ribs, wire pass-throughs, drain channels, radiused edges, and recessed areas for hardware.
Every part you remove from that assembly removes a part number, a purchase order, a receiving transaction, an inventory location, a fixture, and a station on the line. Those costs do not appear on the quote for the part you are replacing, which is why consolidation opportunities get missed during a straight piece-price comparison. An engineer looking at a $40 formed panel next to a $28 stamping is comparing the wrong two numbers when the stamping arrives with brackets, a gasket, and a fistful of fasteners behind it.
The design freedom comes from the tool's single surface. Undercuts and complex internal geometry belong to injection molding, but broad contoured shapes with molded-in functional detail are what a formed sheet is built for. Styling and function land on the same part. On a Class A front cap or an interior wall section, that means the shape the designer wants and the mounting geometry the line needs come out of the same tool.
Bring a molder the whole assembly. Send the solid models, the print, or the existing metal or fiberglass parts, and the useful conversation starts with how many pieces can come out of the stack.
Thermoforming uses a single-surface aluminum tool rather than a matched two-sided steel mold, so tooling runs approximately 10 to 15 percent of injection mold cost for an equivalent part size, and prototype parts come back in 15 to 20 working days instead of months. At RV program volumes, tooling amortization per unit is often the deciding number in the whole comparison.
Run the arithmetic on a hypothetical program. Take a $120,000 injection mold spread across 1,500 units in the first year: that is $80 per part in tooling amortization before a single pound of resin gets counted. The same geometry in a thermoform tool at 12 percent of that cost carries under $10. Piece price on the injection molded part now has to beat the formed part by more than $70 just to break even, and on a panel this size it will not get close.
The lead time carries as much weight as the cost when a program is chasing a show date or a model year cutover. Faster tool builds mean design changes stay affordable late in the cycle. When a heavy equipment OEM needed a redesigned guard for a trade show under three months out, first article prototypes were hand-delivered three weeks before the show.
Low minimum quantity runs are part of the same picture. Thermoforming supports daily production quantities without the volume floor that makes injection molding work, which fits RV model lines, trim levels, and floor plan variants that each need their own part.
Thermoformed parts get trimmed on CNC routers, dies, or fixtures, drilled to fixture for hole position, and edge-finished by deburring, sanding, buffing, flame treating, or gimp. Color, texture, and grain come from the sheet, so a part comes off the tool at its finished appearance without a paint operation. Laminated films add UV protection, anti-graffiti performance, and custom preprinted decoration.
Sheet-integral color is the finishing detail that changes the most about an RV build. A painted metal panel carries a paint line, a cure time, a rework loop, and a color match risk across suppliers. A formed part in a capped or co-extruded sheet arrives at color, and a scratch does not expose a different color underneath. For interiors, that means matched grain across a wall panel, a headliner section, and a cabinet face without a finishing department.
One boundary worth knowing before you spec the part. Painting and silk screening are not in-house operations at every thermoformer, and outsourcing them adds a step and a supplier. When a program depends on a painted or screened graphic, ask about it during the quote rather than after the tool is cut. Co-extruded materials handle a good share of what paint used to be asked for, including UV stability, flammability and toxicity performance, and impact strength.
Our finishing work at PCI covers CNC and die trimming, hole drilling to fixture, edge finishing, laminated films for UV and anti-graffiti, and custom preprinted decoration, with paint and screen printing handled through outside processing when a part calls for it.
A thermoformer can ship a finished sub-assembly rather than a bare panel. Secondary assembly services include epoxy bonding, sonic welding, riveting, steel and nylon fasteners, hinge incorporation, screen installation, lighting, switches, and the integration of metal, foam, and injection molded sub-assemblies into the formed part, delivered kitted and ready to install.
The savings here show up in plant labor, which is why purchasing rarely catches them on a quote comparison. Every operation you move off the chassis line becomes an operation performed at a bench, in sequence, by someone doing it all day with the right fixture. Line labor has been a constrained resource in Elkhart plants through every up cycle the industry has had. Sub-assembly work converts a station on your line into a line item on a purchase order.
It also moves the quality gate upstream. A hinged storage door that arrives with the hinge already set, the seal in place, and the latch installed either passes at the supplier or does not ship. The same door assembled at the station gets found at final inspection, after the surrounding structure is closed up. Ask a molder what a finished, kitted version of the assembly looks like before you scope the part in isolation.
More than 80 percent of RV production in the United States comes out of the Elkhart region (Lippert), so a molder inside that footprint can put an engineer in your plant the same morning, hand-carry first article parts, and ship large light-weight panels without paying long-haul freight on mostly air.
Freight economics on thermoformed parts are unusual and worth naming. A large formed panel weighs very little and takes up a great deal of trailer space, so shipping cost is driven by cube rather than weight. Bring that same part in from a coastal or offshore molder and you are paying to ship air across the country, on a part you specified because it was light. Distance also sets your minimum reaction time to a line-down event, and an RV plant does not sit idle patiently.
The part of local supply that does not appear on any quote is engineering access. Tool tryout, first article review, and fit checks go faster when both parties can be in the same room the day a question comes up rather than the week after. Design changes stay cheap for longer when your molder can walk the line and see the assembly in place.
PCI has built large thermoformed parts in Elkhart since 1972, at 1210 CR 6 West, inside the county where much of the industry assembles.
Thermoformed RV parts hold up when the material is specified for the exposure, and the material list is wide enough to cover most of it. Exterior applications use TPO, Korad capped ABS, ASA/ABS, UV-resistant polycarbonate, and polypropylene. Interiors use ABS, soft flex and one-step vinyl/ABS, polycarbonate, PVC, polyethylene, high impact polystyrene, TPE/TPO, and TPR.
Impact performance is the objection worth putting on a test fixture. On a specialty vehicle program, ABS thermoformed partition panels were subjected to a cargo impact test in which a weight is propelled into the partition, and the panels showed virtually no indentation, with the impact point barely visible. The same panels reduced noise transmission from the cargo area into the cab by more than 3 decibels and held cabin temperature longer than the stamped metal parts they replaced, which is a comfort argument that translates directly to an RV interior.
UV and weathering performance comes from the cap layer and the resin, not from a coating that can chalk or fail at an edge. Co-extruded and capped sheets are specified for UV stability, flammability and toxicity requirements, and impact strength, which is how a formed part survives a decade of parking lots in Arizona.
The honest answer on any conversion is that it needs validation. Specifications, testing, durability, aesthetics, and service access all have to be replicated and verified on the new part, and a molder who tells you otherwise on a first call is selling. Send the print and the exposure requirements, and let the material selection follow the application.
PCI forms single parts up to 6 feet long by 10 feet wide with CNC trim, which covers most of the large panels on an RV, including front and rear caps, wheel wells and fender skirts, storage compartment liners, equipment shrouds, and interior wall and ceiling sections. Sheet thickness and draw ratio, not outline dimension, set the practical limit on any given geometry.
Thermoform tooling runs approximately 10 to 15 percent of injection mold tooling cost for a part of equivalent size, because the process forms a sheet over a single-surface aluminum tool instead of filling a matched two-sided steel mold. At RV program volumes of a few hundred to a few thousand units a year, that difference in amortization usually decides the comparison.
Prototype parts typically come back in 15 to 20 working days, compared with months for an injection mold build. Send a solid model and a scaled 3D printed version can often be produced first for preliminary design and cost review. On one heavy equipment program with a trade show deadline, first article prototypes were hand-delivered three weeks before the show.
Yes, when the application is dimensionally large and structurally moderate, which describes most RV panels. One OEM replaced a 718 pound steel belt guard with a 38 pound impact-resistant ABS thermoformed part, a 95 percent weight reduction, while holding the appearance and branding requirements of the original. Any conversion still needs specification, testing, and durability validation on the new part.
Durability depends on material specification more than on process. Exterior thermoformed parts use TPO, Korad capped ABS, ASA/ABS, UV-resistant polycarbonate, and polypropylene, where UV and weathering performance comes from the cap layer and resin instead of a coating that can chalk at an edge. Formed parts also avoid the cosmetic rework rate that hand-laid fiberglass carries.
PCI's secondary assembly services include epoxy bonding, sonic welding, riveting, steel and nylon fasteners, hinge incorporation, screen installation, lighting, switches, and integration of metal, foam, and injection molded sub-assemblies. A part can arrive kitted and ready to install, which moves assembly labor off the RV chassis line and puts the quality gate at the supplier.
TPO, Korad capped ABS, ASA/ABS, UV-resistant polycarbonate, and polypropylene are the common exterior choices. Co-extruded materials are available where a program needs specific UV stability, flammability and toxicity performance, or impact strength. Interior applications use ABS, soft flex and one-step vinyl/ABS, polycarbonate, PVC, polyethylene, high impact polystyrene, TPE/TPO, and TPR.